How To Read Degrees On A Plat Map

The scale will be the ratio between the distance on the map and the distance of the actual property. Learning to read a land survey map is not only for surveyors.


A to Z GIS (eBook Rental) in 2020 Data science

The plat is actually based on a previous plat drawn in 1850 so you're another 2 degrees off.

How to read degrees on a plat map. So if 'q = deedpoints[0]', then 'q[0] = n' and 'q[5] = 1401.09'. This will give you an idea of just how far you have to go. The earth is nearly 25,000 miles around, so once divided into 360 degrees, it means each degree is about 69 miles wide.

A plat is a map of a land area, usually on the scale of a neighborhood or county township, and a plot is a piece of land used for a single purpose (such as a park or a home). You probably remember from school that a circle is 360 degrees, a degree is 60 minutes and a minute is 60 seconds. For millimeters, divide the large number on the map scale (i.e.

The scale of your plat map will be in the map’s legend. Sometimes a client will note that measured bearings and distances vary somewhat from the recorded measurements shown within the deed or on the plat. Consider which format you want to use.

Now click on the other parcel corners that interest you to see those coordinates. For our 1:9,000 map example, the inches divide by number equals 45.5. 100,000.” this ratio simply means that 1 unit of distance on the map is equal to 100,000 units in real life.

Information relative to roads, lighting, landscaping, natural features, access, soil erosion control, and stormwater management. Click on the remaining corners. The angle is calculated as degrees+minutes/60+seconds/3600.

Survey plats can also be read in reverse. If your map shows seconds, find the second closest to where each line intersects the latitude or longitude scale at the edge of the map. A site plan package can include:

Each degree is then broken down into 60 minutes. To read the coordinates of any location, start with the number of degrees on the latitude line, and clarify whether it is in the northern or southern hemisphere. Thence continue s 0 degrees 03’08” e, 409.67 feet;

The elements of a list or a tuple are indexed by a number starting with zero. A map’s scale provides a ratio of map distance to actual distance. The scale will differ from map to map, but will typically be presented as a number ratio, like “1 :

This can be read more descriptively as north 66 degrees 0 minutes and 0 seconds for a distance of 1245.01 feet. The angle can be stated as a certain number of degrees (°), followed by an additional number of minutes ('), followed by a certain number of seconds (). Deedpoint is a list of tuples, while 'd' is a tuple.

Thence n 89 degrees 54’41” w, 314.69 feet to the east line of a 20 foot easement; Land survey maps are used to measure everything from. An example heading might be n63e.

Our compass puts north at 0 degrees. Read the compass degree system by starting with a specific point on the compass (north, east, south or west), and then reading the number of the degrees to the next point on the compass. So, to make our heading work, we need to add 36 to 180, giving us 216 degrees.

For example, if your latitude line falls about 5″ above the 32°20′n line, your point is at a latitude of approximately 32°20′5″n. Directly to your right (east) would be 90 degrees east of north. You miss figure the declination from the magnetic bearing shown on the plat by 2 degrees.

An example of bearing and distance might be n 66° 0′ 0″ e 1245.01′. The second format is degrees, minutes and seconds: Since south from there would be 180 degrees, 36 degrees does not make much sense.

For our 1:9,000 map example, the millimeter divide by number equals 1.8 (1 millimeter = 1.8 poles). This reads north, 63 degrees east. surveyors can mark the compass degree system as precisely as they want. For inches, divide the large number on the map scale (i.e.

Use a ruler to get the most accurate reading of your plat map. Subdivision plats must be completed by a licensed surveyor and meet the survey plat recording requirements of 27 v.s.a. The corners of your plat map will have the book and page number.

As you continue to turn you would face west, located 90 degrees west of north. Thence run n 0 degrees. To better understand this concept, imagine that you are facing north.

A survey bearing indicates the quadrant in which it exists and the number of degrees into that quadrant measured from zero. Site plan is a drawing that is a bird’s I prefer the decimal format.

The distances are usually indicated in u.s. These are usually drawn and then each line is annotated with bearing and distance. If you turned around you would be facing south and would be 180 degrees south of north.

4 degrees of error down one side of your parcel equates to about a 460' error in where you think the property corner should be. This is then converted to cartesian degrees by the nested if/then. You read an old plat from the 40's with metes and bounds rounded to the nearest degree.

N42w, or 42 degrees west of north; How to read a land survey map.


GOOGLE CLASSROOM Distance Learning 2nd Grade MAP SKILLS


1908 Plat map showing mine locaton Photo album, Southern


GIS Bad map examples Choropleth map


UTM/MGRS Coordinate Scale Compass Rose in both Degrees and


A color coded county map of all of the school districts in


Pin on MnemonicsNursing


Vintage 19831984 Nuckolls County Nebraska Atlas with Plat


Printable 360 Degree Wheel with Compass Rose Compass


QGIS exporting contours to DXF with height values


EKG Basics Nursing mnemonics, Nursing students, Cardiac


From Dayton to Cambridge and Back Again the field notes


Mapping XY tabular data with ArcGIS Geospatial / GIS


How to Use SPSSCronbach's Alpha Reliability Test in 2020


Miss Nelson Has A Field Day, Level L, Differentiated


Global Geographic information system (GIS) Market


Word problem steps Word problem steps, Word problems


Image from


On Old Map' Prints AlexStar in


Batch Make Grids and Graticules Layer for ArcGIS 10.1